DOOR HANDLE CUP PROTECTION COVERS to suit 2021-2025 Isuzu Mu-X

• Compatible with 2021-2025 Isuzu Mu-X

Why wait until common scratches appear above and behind your door handle? Our door cup protection sets are precisely molded to fit your door cups, providing both stylish flair and effective protection.

Enjoy quick and easy DIY installation with the included 3M adhesive strip.

Please note: These sets are not compatible with Rhino hide or other aftermarket accessories that may come into contact with the application areas.

When purchasing the product, rest assured that the 3M adhesive tape comes pre-applied by the manufacturer. We recommend checking the adhesive tackiness before installation. If you have concerns about its strength, you can either add more tape or replace it with adhesive tape of your preference.

Please be aware that we do not inspect all adhesive tapes, so the decision regarding tape strength is left to the consumer. We do not cover the tape as a warranty item.

Ensure compatibility by reviewing photos and confirming it's the right item for your car. Refunds are not offered for incorrect product choices.

These are compatible with all current models, including those released after 2021, of the Isuzu MU-X.

Each piece is clearly labelled for proper placement:

• RR-RH = Rear Right-hand door.
• RR-LH = Rear Left-hand door.
• FR-RH = Front Right-hand door.
• FR-LH = Front Left-hand door.        

• Door Bowl Cup Protector – Installation Guide
  Compatible with: Isuzu D-MAX, Mazda BT-50, Isuzu MU-X
  
  Now is the Time to wash your vehicle !!- Further reference at the end.
  
  
• Step 1: Inspect & Identify Parts Carefully inspect all parts received. Make sure you have the correct quantity and shapes for your vehicle (front/rear, left/right). Some designs are position-specific — refer to product photos and part shapes. If you're unsure, please contact us before continuing.
  
  
• Step 2: Test Fit & Familiarize Lock your vehicle to allow the handle to be pulled out without opening the door. Begin with test fitting each protector: Pull the handle out. Slide the protector in from the top and front of the door bowl area. Once the front is positioned over the handle, lower the rear into place. Use body lines and the handle to align. Apply light pressure to check fitment. Review our product photos to confirm correct orientation. If you have concerns, pause and contact us before attempting to fit.
  
  
• Step 3: Repeat Test Fit for All Doors

  Repeat the above test fit process for every door bowl.

  This ensures all pieces are correct and avoids fitting errors.

  Yes, it takes a little extra time — but it makes the final installation smooth and hassle-free.

  
  Step 4: Clean the Surface Thoroughly

  This step is critical for proper adhesion.

  Mix 50/50 water and isopropyl alcohol.

  Wipe each door bowl area thoroughly to remove dirt, wax, or coatings (including ceramic paint protection).

  Use a clean microfiber cloth to dry the area fully.

  Do not skip this step — poor preparation will lead to adhesive failure!!

  
  Step 5: Prepare Adhesive Tabs

  On the back of each protector, lift a small portion of the red backing tape on each adhesive strip.

  Fold these tabs forward — this makes it easier to pull off later without sticking prematurely.

  
  Step 6: Final Fitment

  Carefully position the protector into place, keeping it slightly away from the surface.

  Once you're confident it's correctly aligned, lightly press it into place.

  Now remove the red tape backing using the folded tabs from earlier.

  Once all backing is removed, press firmly along the adhesive edges and in the center using a microfiber cloth.

  Repeat this step for all doors, then go back and press again on the first one installed to ensure maximum bond.

  
  FINAL NOTE:

  If your car wasn’t washed before installation, do not wash it now.

  Avoid water or car washes for at least 24 hours to allow full adhesive bonding.

  We recommend washing the vehicle before starting the installation process next time.